Acoustic treatment on a budget: two changes that solve 80% of room problems
23/05/2026
Acoustic treatment is one of those topics that can spiral quickly into complexity and expense. Bass traps in the corners, broadband absorbers on the first reflection points, diffusers on the rear wall — there is a whole science to it and a whole industry selling products for it. Most of that is relevant for professional studio builds, not for home recording setups.
The truth is that two straightforward, low-cost changes will address the majority of the acoustic problems that show up in home recordings. You do not need foam tiles covering every surface. You need to understand what the problems actually are and where they come from.
What the problems actually are
Room acoustics in a typical home recording space cause two main categories of problem.
High-frequency reflections. Sound from your microphone (or your monitors, if you are mixing) travels outward, hits the nearest hard surface — a desk, a wall, a window — and bounces back toward the microphone with a slight delay. This produces comb filtering: a pattern of frequency cancellations that makes the recording sound coloured and unnatural. It is the primary cause of that boxy, hollow quality that home recordings often have.
Low-frequency build-up. Long wavelength bass frequencies pile up in the corners and at the boundaries of a room. This causes certain bass notes to sound much louder than others and makes the low end of a recording or mix sound inconsistent and difficult to control. This is the harder of the two problems to solve, and it requires more significant intervention to fully address. But it is also less critical for many home recording applications.
Change one: treat the first reflection points
The first reflection points are the surfaces that sound hits before bouncing back toward the microphone. In a typical home recording setup, these are the walls immediately to the left and right of the recording position, the wall directly in front (behind the microphone), and the ceiling directly overhead.
Reducing the reflections from these surfaces dramatically reduces the comb filtering and boxy quality in recordings. You do not need acoustic panels for this. You need absorption — something that absorbs sound rather than reflecting it.
A heavy curtain or blanket behind the recording position is the most impactful single change you can make. Hang it on the wall behind where you sit or stand while recording, close enough that it sits within the direct reflection path between the microphone and the wall. This does not need to cover the entire wall — a section roughly two metres wide and two metres tall makes a significant difference.
For the side walls, the same principle applies. A bookcase full of books, a wardrobe full of clothes, a heavy rug hung on the wall — all of these absorb high-frequency sound and reduce reflections. The material matters more than the purpose. Soft, irregular, porous surfaces absorb. Hard, flat, smooth surfaces reflect.
If you want to verify this is working, record a short vocal or spoken word section before and after. The improvement is usually obvious and immediate.
Change two: put something soft on the floor
Hard floors — laminate, wood, tile — are major reflection surfaces, particularly directly under and in front of the recording position. A large, thick rug under and around the recording position addresses a significant reflection path and also reduces low-frequency room resonance to a modest degree.
A rug in the recording area is probably the cheapest single acoustic improvement available. Combined with the treatment at the reflection points above, it addresses the main causes of high-frequency room sound in most home setups.
What about bass?
The low-frequency build-up problem is harder to solve cheaply. True bass traps — broadband absorbers designed to absorb long wavelength frequencies — need to be physically large to work at low frequencies. A thin piece of foam does not absorb bass. The physics require mass and depth.
For recording purposes — capturing instruments and vocals — this matters less than it does for mixing. If you are recording and sending files to be mixed and mastered elsewhere, the low-frequency characteristics of your room are less critical. The mix and mastering stages apply to the finished track, not the recording environment.
If you are mixing in your home studio and relying on what you hear in the room to make mixing decisions, the low-frequency issue becomes more significant. In that case, the practical solutions are: work in a smaller room (which has its own problems but tends toward different ones), use headphones for low-frequency judgement, and reference your mixes extensively on different systems before finalising them.
The things that do not work
A few commonly suggested solutions are worth addressing directly because they do not work as advertised.
Egg cartons. They do not absorb sound. They scatter it slightly at high frequencies and do essentially nothing useful for recording acoustics.
Thin acoustic foam tiles. The cheapest foam panels sold for acoustic treatment are typically too thin to absorb the frequencies that cause the most problems in home recordings. They absorb very high frequencies — which are usually not the primary issue — and do very little below 2kHz. They are better than nothing, but significantly less effective than a heavy curtain at a fraction of the cost.
Filling the room with furniture. More objects in a room help scatter sound and can reduce reverberation time. But random furniture does not address specific reflection paths. Treating the first reflection points is more targeted and more effective.
A practical starting point
If you are recording in a typical home room and want to meaningfully improve the acoustics without spending significant money:
Hang a heavy curtain or thick blanket on the wall behind the recording position. Put a large rug under the recording area. These two changes address the most common causes of poor home recording acoustics and will produce a noticeable improvement in the clarity and character of recordings made in the space.
Beyond that, specific improvements depend on the specific room and the specific problems in it. If you record a short test and want a second opinion on what the room sounds like in the recording, send it over.