How to get a usable recording from a live gig even with a basic setup

23/05/2026

Most live recordings are not ruined in the edit. They are ruined before the soundcheck ends. A few decisions made before you go on stage — about what you record, how you record it, and what you accept as a limitation — are the difference between a file that can be turned into something you are proud of and one that gets quietly deleted a month later.

This is not a guide about expensive gear. It is about making smarter decisions with whatever you have available.

Understand what you are actually trying to capture

Before anything else, decide what the recording is for. That decision shapes everything else.

If you want a document of the performance — something to look back on, share with the band, use for rehearsal — almost anything will do. Reasonable quality is enough.

If you want something to release, post on YouTube, or use as a professional reference, the bar is higher. Not impossible, but the decisions you make on the night matter more, and some limitations cannot be fixed in editing.

Knowing which one you are going for before the gig means you will not be disappointed by a result that was never meant to be what you expected.

The two sources worth knowing about

There are two main ways to record a live show, and understanding the difference changes your approach completely.

A feed from the mixing desk. If the venue has a sound engineer running a desk, ask whether they can give you a feed — typically an auxiliary output or a split from the main mix. What you get depends entirely on what is going through the desk. In many smaller venues, only vocals and keys go through the desk. Drums and guitars are often coming off stage amplifiers and not going through the PA at all. A desk recording in that situation will sound thin and incomplete.

A stereo room recording. Two microphones placed in front of the stage capture everything — the full band, the room, the crowd. This is less controllable but often more representative of how the show actually sounded. A pair of condenser microphones on a stereo bar, placed roughly 5 to 10 metres from the stage at head height, is a simple starting point.

Many engineers use both — a desk feed as a clean reference and a room recording for atmosphere — and blend them in the edit. If that is available to you, take it.

The problems that will show up in almost every live recording

It is worth being honest about what you are likely to get, so you can either manage it or accept it.

Room noise. Crowd movement, bar noise, air conditioning, stage noise — all of it lands in the microphone. Some of it is part of the character of a live recording. Some of it is distracting and reducible. It is rarely eliminable entirely.

Timing drift. Live performances are not metronomically perfect, and that is usually fine. But if a section falls noticeably out of time, it will be obvious in the edit. Subtle timing correction is possible. Dramatic correction usually sounds worse than leaving it alone.

Crowd bleed. If someone near the microphone is talking, singing along loudly, or audibly reacting, it will be in the recording. There is no way to remove a specific conversation from a room microphone after the fact. This is a limitation you have to accept.

Inconsistent levels. The loudest moment of the night and the quietest moment may be 20 to 30 dB apart. Compression at the mastering stage will bring this closer together, but if individual moments are distorting or too quiet to hear, that is harder to recover.

Decisions to make before the gig

Check your recording level before you start. Run a sound check through your recording device and look at the levels. Aim for peaks around -12 to -6 dBFS on the loudest expected moments. This leaves headroom for the moments that are louder than you expect — and there will be some.

Do not use automatic gain control. If your recording device or phone camera has automatic gain control, turn it off. It will pump and breathe during quiet and loud sections, and those level changes are very difficult to edit out after the fact.

Record at the highest quality your device allows. WAV at 24-bit, 48kHz is ideal. If your device only records MP3, use the highest bitrate available. Compressed audio formats introduce artefacts that become more obvious when you apply processing in the edit.

Leave your microphones alone once the show starts. Adjusting mic position mid-show is almost always audible in the recording as a shift in the sound. Set them up, check the levels, and leave them.

Arrive early enough to do all of this properly. Running a recording device backstage five minutes before doors open is not the same as having 30 minutes to check levels, test the room, and fix whatever is wrong.

What editing can and cannot fix

A good editor can reduce room noise to a manageable level, correct timing issues that are subtle and isolated, improve the tonal balance of the recording, and bring up quiet sections while taming the loudest moments. The result can sound genuinely good — natural and live, but clean enough to hold up on streaming platforms or YouTube.

What editing cannot fix: a recording that was clipping throughout, a performance where whole sections are out of time, a room so reverberant that every note blurs into the next one, or a recording where the levels were so mismanaged that the signal is buried under noise.

The best recordings to work with are ones where the person recording was paying attention throughout. They do not need to be technically perfect. They need to have been made with care.

The simplest version of all of this

Bring a recorder you know how to use. Set your levels before the show. Record WAV if you can. Place your microphones somewhere sensible, check them, and leave them. Know what the recording is for.

That is most of it. The rest is just practice.

If you have got a live recording you are not sure what to do with, send it over. The first thing I do is listen — not to judge the recording, but to understand what it has and what it needs.