The frequency ranges every musician should know before their first mix session

23/05/2026

You do not need to be an audio engineer to understand frequency ranges. But knowing the basics will make you a better communicator when you are working with one — and it will help you understand why a mix sounds the way it does, which is the first step to being able to change it.

This is a practical reference guide, not an acoustics textbook. It covers the ranges that matter most for common instruments and gives you language to describe what you are hearing.

The full spectrum, briefly

Human hearing covers roughly 20Hz to 20,000Hz (20kHz). In practice, the range that matters most for music sits between about 40Hz and 16kHz. The extremes — below 40Hz and above 16kHz — are either felt rather than heard or carry mostly air and harmonic detail.

The spectrum is usually divided into a few broad regions:

  • Sub-bass: 20–60Hz
  • Bass: 60–250Hz
  • Low midrange: 250–500Hz
  • Midrange: 500Hz–2kHz
  • Upper midrange: 2kHz–6kHz
  • Presence and air: 6kHz–20kHz

Understanding where different instruments live in these regions helps explain why certain combinations clash, and why cutting or boosting in specific areas changes how something sounds.

Sub-bass: 20–60Hz

This is felt as much as it is heard. Kick drums, bass guitars, and synthesiser bass lines extend into this region. On small speakers — laptop speakers, earbuds, phone speakers — very little of this range reproduces at all. On a large system or subwoofer, this is where the physical impact of music comes from.

Problems in the sub-bass are common in home recordings and usually come from room acoustics. Low frequencies build up in corners and cause certain notes to sound much louder than others — an effect called room modes. This can make the bass sound inconsistent: some notes booming, others disappearing.

If your bass sounds uneven or uncontrollable, sub-bass frequency build-up in the room is often part of the cause.

Bass: 60–250Hz

This is where the body and weight of most music lives. Kick drum punch, the fullness of a bass guitar, the warmth of a male vocal — these are all in this range.

Too much in this region and a mix sounds muddy and heavy. Too little and it sounds thin and lacks warmth. Getting this range right is one of the most important things in a mix, and it is also one of the most affected by room acoustics.

Instruments with significant energy here: Bass guitar (fundamental notes 40–300Hz), kick drum (punch around 60–100Hz), electric guitar body, piano lower register, male vocals (fundamental 80–180Hz).

Low midrange: 250–500Hz

This is a range that mixes can easily get wrong. It contains a lot of the warmth and fullness of instruments, but too much energy here makes everything sound boxy, thick, and congested. Muddy mixes often have too much low midrange rather than too much bass.

This is also the range where room acoustics cause problems in many home recording setups. If everything sounds like it was recorded in a cardboard box, this frequency region is usually contributing.

Instruments with significant energy here: Guitars (especially the body of acoustic guitars), snare drum body, piano midrange, brass instruments.

Midrange: 500Hz–2kHz

The midrange is where a huge amount of the character and intelligibility of instruments lives. Vocals, guitars, and most melodic instruments are highly present in this region. It is also where a mix can become harsh or nasal if there is too much energy in the wrong place.

The midrange is what small speakers reproduce most accurately, which is why a mix that sounds good on laptop speakers but falls apart on a big system is often a mix where the midrange was over-relied upon.

Instruments with significant energy here: Vocals (key presence 1–3kHz), electric guitar, piano, most melodic instruments.

Upper midrange: 2kHz–6kHz

This is the range most associated with presence and cut-through. A boost around 3–4kHz makes a vocal sit in front of a mix. Too much energy here, particularly around 2–4kHz, is where listening fatigue comes from — mixes that sound aggressive or exhausting after a short time.

This range is also where the attack of transients — the initial hit of a drum, the pick attack on a guitar — is most apparent. Boosting here adds definition and presence. Cutting reduces harshness.

Instruments with significant energy here: Snare attack, vocal presence, guitar pick attack, piano attack.

Presence and air: 6kHz–20kHz

The high frequency range adds brightness, sparkle, and detail. Cymbals, the breath in vocals, the shimmer of acoustic guitars, the subtle details that make a recording feel alive and open — these are in the upper end of the spectrum.

Too much high frequency and a mix sounds harsh, brittle, or sibilant (excessive sss sounds in vocals). Too little and it sounds dull, closed-in, and lacks air.

Instruments with significant energy here: Cymbals and hi-hats, vocal breath and sibilance, acoustic guitar shimmer, synthesiser pads.

How this applies in practice

When you are listening to a mix and something feels wrong, being able to locate it in the frequency spectrum helps you describe it:

  • “Muddy” usually means too much in the 200–400Hz range
  • “Thin” usually means not enough in the bass and low midrange
  • “Harsh” or “aggressive” usually means too much in the 2–5kHz range
  • “Dull” or “muffled” usually means not enough in the high midrange and presence range
  • “Boomy” usually means too much sub-bass or bass, often below 100Hz

This language is much more useful to an engineer than “make it sound better.” When you can say “the guitars feel boxy and are sitting on top of the bass” or “the vocal is a bit nasal around the lower midrange,” you are describing something specific that can be addressed with specific tools.

The more precisely you can describe what you are hearing, the faster any edit or mix session goes.